DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
 |
  |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
 | Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-08日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 。∕2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
DI-9M-8日本CEDAR電批扭力測試儀
| DI-9 series is most suitable for checking ａnd controlling the torque of Electric Screwdriver ａnd Torque Driver. |
| upgrade The main changed parts （1） In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. （2） Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. （3） Setup of Various Numerical Values Can be Easy ａnd Can Carry Out Speedily. （4） Calculation of Maximum, Minimum, ａnd Average Became Intelligible. （5） The call of the saved data became easy. The output of data also became intelligible. （6） Fault charge protection. It is pilot-lamp lighting during charge. （7） Data Output is USB Form （B Type）. （8） Memory Data are 800 Affairs （9） Real-time Output is Every 1 / 180 Seconds. |
|
| |
| The best for everyday check of an electric driver Wide measurement range （0 - 8000digit）, it corresponds to various set torques Can measure without inversion/ rolling-back work efficiently by OW joint （PAT.P）. |
| Specification | DI-9M-8 | DI-9M-08 | |
| Measuring range | 0.020-8 N?m | 2.0-800 mN?m | |
| 0.20～80 kgf?cm | 0.020～8 kgf?cm | ||
| 0.20～70 lbf?in | 0.020～7 lbf?in | ||
| Accuracy | ±0.5% （499 digit or less ±3digit） | ||
| Display | The 4 figures digital display of LCD | ||
| The measurement direction | CW-CCW （right ａnd left） | ||
| Zero return by one touch | Return to zero by pressing clear button. | ||
| Measurement Mode | Track , P-P（peak to peak） , P-D（Peak-Down） , C（Real-time Output） | ||
| High ａnd low limits judging function | High ａnd low value are measurement within the limits, ａnd can be set up. | ||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | ||
| The Maximum, the minimum, ａnd the average value display | The maximum, the minimum, average value, ａnd the data number of 30 data are displayed.It saves to ten channels. | ||
| Data Output | ASCII format （baud rate 19200） | ||
| Auto power save | 10 minutes no use, automatically switch off. | ||
| Power supply | Ni-Cd chargeable battery 1.2V × 5cells 700mAh | ||
| Charging time | About 3hours | ||
| Continuous working time | About 12hours | ||
| clearance | It is a display clearance in set-up time. （0.1 - 3.0 sec） | ||
| Socket size | □ 20mm/ □9.5mm | ||
| Dimension / Weight | W:160×D:125×H:55 / About 1kg | ||
| Recommend buffer accessories | Measuring joint OW-20/OW-60 | Measuring joint OW-025/OW-10 | |
| Cube （with a 5th page screw hole） 20x20x20 （M2.6/M3/M4/M5/M6 Tap processing） | |||
| AC/DC adaptor | |||
| Exclusive receipt case | |||
| An inspection report, a proofreading certificate, a traceability system figure | |||
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ● MEASURING JOINT OW series | |
| Since our company developed the buffer with little influence of fricative, stable measurement could be performed Moreover ,it does not need to reverse-rotate at the time of measurement, ａnd work efficiency improved. |
| Specification | Type | ||||
| OW-025 | OW-10 | OW-20 | OW-60 | ||
| Measuring range N?m | 0.25 | 1 | 2 | 6 | |
| Mechanical life （times） | 10,000 | 8,000 | 5,000 | 5,000 | |
| Outer diameter size （mm） | Bit engagement part （screw part） | M2.6 cross recess screw | M3 cross recess screw | M4 cross recess screw | M6 cross recess screw |
| The standard screw is cross recess screw but they may be altered as necessary | |||||
| Outside diameter | φ28 | φ32 | φ32 | φ38 | |
| Height | 44 | 51 | 51 | 69 | |
| Ｉnstallation | 20square ×4（t） | ||||
最新產品
- 橡膠高低溫抗拉伸力強度試驗機 2024/11/24 14:41:42
- 中心血站冰凍血漿水浴解凍箱 2024/11/24 14:33:52
- 血站冰凍血制品解凍箱 2024/11/24 14:33:25
- CMC-185-MX成都軟起動經銷MCD201-110-T4-CV3 SSD-55KW ATS22C25Q XYR6-37KW 2024/11/24 14:31:27
- 冰凍血制品恒溫解凍箱 2024/11/24 14:30:42
- 隔水式恒溫血漿解凍箱 2024/11/24 14:30:13
- 輸血科冰凍血漿解凍儀 2024/11/24 14:29:31
- 醫用冰凍血制品解凍儀 2024/11/24 14:28:47
- 水浴式血制品血漿解凍箱 2024/11/24 14:27:29
- 臺式血漿解凍箱 2024/11/24 14:27:07
- 循環水式血漿解凍箱 2024/11/24 14:26:12
- 血液科血液制品血漿解凍箱 2024/11/24 14:25:43
- 發布動態/抗檢測原料/ 抗檢測抗115項抗檢測原粉@報價已更新 2024/11/24 13:45:34
- 發布動態/強力v1/抗檢測強力v1/高品質原料@產品價格 2024/11/24 13:44:18
- 發布動態/鹽酸達泊西汀/達泊西丁原料@產品價格 2024/11/24 13:43:06
- 發布動態/無水茶堿/茶葉提取物/茶堿/茶堿原料/動態已更新 2024/11/24 13:41:57
- 發布動態/奧利司他/奧利司他原料@產品價格 2024/11/24 13:40:39
- 發布動態/他達那非/他達那非原料/產品價格 2024/11/24 13:39:29
- 發布動態/育亨賓/鹽酸育亨賓原料@產品價格 2024/11/24 13:38:17
- 發布動態/無水茶堿/茶葉提取物/茶堿/茶堿原料/已更新報價 2024/11/24 13:37:08
- 發布動態/西地那非/西地那非原粉/西地原料/產品價格 2024/11/24 13:35:47
- 發布動態/金陽堿/金陽堿原料@產品價格 2024/11/24 13:34:37
- 發布動態/抗檢測原料/ 抗檢測抗115項抗檢測原粉@產品價格 2024/11/24 13:33:36
- 發布動態/強力v1/抗檢測強力v1/高品質原料@動態播報 2024/11/24 13:32:23
- 發布動態/鹽酸達泊西汀/達泊西丁原料@動態播報 2024/11/24 13:31:19
- 發布動態/無水茶堿/茶葉提取物/茶堿/茶堿原料/產品功能 2024/11/24 13:29:38
- 發布動態/奧利司他/奧利司他原料@動態播報 2024/11/24 13:28:05
- 發布動態/他達那非/他達那非原料/動態播報 2024/11/24 13:27:05
- 發布動態/育亨賓/鹽酸育亨賓原料@動態播報 2024/11/24 13:25:57
- 發布動態/無水茶堿/茶葉提取物/茶堿/茶堿原料/動態播報 2024/11/24 13:24:48