人甲基睪丸酮(Methyltestosterone)ELISA檢測試劑盒
本試劑盒僅供研究使用。
人甲基睪丸酮(Methyltestosterone)ELISA檢測試劑盒實驗原理
本試劑盒應用雙抗體夾心法測定標本中人甲基睪丸酮(Methyltestosterone)水平。用純化的人甲基睪丸酮(Methyltestosterone)抗體包被微孔板,制成固相抗體,往包被單抗的微孔中依次加入甲基睪丸酮(Methyltestosterone),再與HRP標記的甲基睪丸酮(Methyltestosterone)抗體結合,形成抗體-抗原-酶標抗體復合物,經過徹底洗滌后加底物TMB顯色。TMB在HRP酶的催化下轉化成藍色,并在酸的作用下轉化成最終的黃色。顏色的深淺和樣品中的甲基睪丸酮(Methyltestosterone)呈正相關。用酶標儀在450nm波長下測定吸光度(OD值),通過標準曲線計算樣品中人甲基睪丸酮(Methyltestosterone)濃度。
人甲基睪丸酮(Methyltestosterone)ELISA檢測試劑盒試劑盒組成
1 | 30倍濃縮洗滌液 | 20ml×1瓶 | 7 | 終止液 | 6ml×1瓶 |
2 | 酶標試劑 | 6ml×1瓶 | 8 | 標準品(96 nmol/L) | 0.5ml×1瓶 |
3 | 酶標包被板 | 12孔×8條 | 9 | 標準品稀釋液 | 1.5ml×1瓶 |
4 | 樣品稀釋液 | 6ml×1瓶 | 10 | 說明書 | 1份 |
5 | 顯色劑A液 | 6ml×1瓶 | 11 | 封板膜 | 2張 |
6 | 顯色劑B液 | 6ml×1/瓶 | 12 | 密封袋 | 1個 |
標本要求
1.標本采集后盡早進行提取,提取按相關文獻進行,提取后應盡快進行實驗。若不能馬上進行試驗,可將標本放于-20℃保存,但應避免反復凍融
2.不能檢測含NaN3的樣品,因NaN3抑制辣根過氧化物酶的(HRP)活性。
人甲基睪丸酮(Methyltestosterone)ELISA檢測試劑盒操作步驟
1. 標準品的稀釋:本試劑盒提供原倍標準品一支,用戶可按照下列圖表在小試管中進行稀釋。
48 nmol/L | 5號標準品 | 150μl的原倍標準品加入150μl標準品稀釋液 |
24 nmol/L | 4號標準品 | 150μl的5號標準品加入150μl標準品稀釋液 |
12 nmol/L | 3號標準品 | 150μl的4號標準品加入150μl標準品稀釋液 |
6 nmol/L | 2號標準品 | 150μl的3號標準品加入150μl標準品稀釋液 |
3 nmol/L | 1號標準品 | 150μl的2號標準品加入150μl標準品稀釋液 |
2. 加樣:分別設空白孔(空白對照孔不加樣品及酶標試劑,其余各步操作相同)、標準孔、待測樣品孔。在酶標包被板上標準品準確加樣50μl,待測樣品孔中先加樣品稀釋液40μl,然后再加待測樣品10μl(樣品最終稀釋度為5倍)。加樣將樣品加于酶標板孔底部,盡量不觸及孔壁,輕輕晃動混勻。
3. 溫育:用封板膜封板后置37℃溫育30分鐘。
4. 配液:將30倍濃縮洗滌液用蒸餾水30倍稀釋后備用
5. 洗滌:小心揭掉封板膜,棄去液體,甩干,每孔加滿洗滌液,靜置30秒后棄去,如此重復5次,拍干。
6. 加酶:每孔加入酶標試劑50μl,空白孔除外。
7. 溫育:操作同3。
8. 洗滌:操作同5。
9. 顯色:每孔先加入顯色劑A50μl,再加入顯色劑B50μl,輕輕震蕩混勻,37℃避光顯色15分鐘.
10. 終止:每孔加終止液50μl,終止反應(此時藍色立轉黃色)。
11. 測定:以空白空調零,450nm波長依序測量各孔的吸光度(OD值)。 測定應在加終止液后15分鐘以內進行。
操作程序總結:
計算
以標準物的濃度為橫坐標,OD值為縱坐標,在坐標紙上繪出標準曲線,根據樣品的OD值由標準曲線查出相應的濃度;再乘以稀釋倍數;或用標準物的濃度與OD值計算出標準曲線的直線回歸方程式,將樣品的OD值代入方程式,計算出樣品濃度,再乘以稀釋倍數,即為樣品的實際濃度。
注意事項
1.試劑盒從冷藏環境中取出應在室溫平衡15-30分鐘后方可使用,酶標包被板開封后如未用完,板條應裝入密封袋中保存。
2.濃洗滌液可能會有結晶析出,稀釋時可在水浴中加溫助溶,洗滌時不影響結果。
3.各步加樣均應使用加樣器,并經常校對其準確性,以避免試驗誤差。一次加樣時間最好控制在5分鐘內,如標本數量多,推薦使用排槍加樣。
4. 請每次測定的同時做標準曲線,最好做復孔。如標本中待測物質含量過高(樣本OD值大于標準品孔第一孔的OD值),請先用樣品稀釋液稀釋一定倍數(n倍)后再測定,計算時請最后乘以總稀釋倍數(×n×5)。
5. 封板膜只限一次性使用,以避免交叉污染。
6.底物請避光保存。
7.嚴格按照說明書的操作進行,試驗結果判定必須以酶標儀讀數為準.
8.所有樣品,洗滌液和各種廢棄物都應按傳染物處理。
9.本試劑不同批號組分不得混用。
10. 如與英文說明書有異,以英文說明書為準。
保存條件及有效期
1.試劑盒保存:;2-8℃。
2.有效期:6個月
|
Human Methyltestosterone
FOR RESEARCH USE ONLY
Assay range:2 nmol/L -48 nmol/L 96 determinations
Purpose
This kit allows for the determination of Methyltestosterone concentrations in Human serum, cell culture supernates and other biological fluids
Principle of the assay
The kit assay Human Methyltestosterone level in the sample,use Purified Human Methyltestosterone antibody to coat microtiter plate wells, make solid-phase antibody, then add Methyltestosterone to wells, Combined Methyltestosterone antibody which With HRP labeled,become antibody - antigen - enzyme-antibody complex, after washing Completely, Add TMB substrate solution,TMB substrate becomes blue color At HRP enzyme-catalyzed, reaction is terminated by the addition of a sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450 nm. The concentration of Human Methyltestosterone in the samples is then determined by comparing the O.D. of the samples to the standard curve.
Materials provided with the kit
1 | wash solution | 20ml×1bottle | 7 | Stopp Solution | 6ml×1 bottle |
2 | HRP-Conjugate reagent | 6ml×1 bottle | 8 | Standard( 96 nmol/L) | 0.5ml×1 bottle |
3 | Microelisa stripplate | 12well×8strips | 9 | Standard diluent | 1.5ml×1bottle |
4 | Sample diluent | 6ml×1 bottle | 10 | Instruction | 1 |
5 | Chromogen Solution A | 6ml×1 bottle | 11 | Closure plate membrane | 2 |
6 | Chromogen Solution B | 6ml×1 bottle | 12 | Sealed bags | 1 |
Specimen requirements
1. extract as soon as possible after Specimen collection,and according to the relevant literature, and should be experiment as soon as possible after the extraction. If it can’t, specimen can be kept in -20 ℃ to preserve, Avoid repeated freeze-thaw cycles.
2. Can’t detect the sample which contain NaN3, because NaN3 inhibits HRP active.
Assay procedure
1. Dilute and add sample:Dilute Original density Standard as follow table:
48 nmol/L | 5 Standard | 150μl Original density Standard+150μl Standard diluent |
24 nmol/L | 4 Standard | 150μl 5 Standard+150μl Standard diluent |
12 nmol/L | 3 Standard | 150μl 4 Standard+150μl Standard diluent |
6 nmol/L | 2 Standard | 150μl 3 Standard +150μl Standard diluent |
3 nmol/L | 1 Standard | 150μl 2 Standard +150μl Standard diluent |
2.add sample:Set blank wells separately (blank comparison wells don’t add sample and HRP-Conjugate reagent, other each step operation is same). testing sample well. add Sample dilution 40μl to testing sample well, then add testing sample 10μl (sample final dilution is 5-fold), add sample to wells , don’t touch the well wall as far as possible, and Gently mix.
3.Incubate: After closing plate with Closure plate membrane ,incubate for 30 min at 37℃.
4.Configurate liquid: 30-fold(or 20-fold) wash solution diluted 30-fold (or 20-fold) with distilled water and reserve.
5.washing:Uncover Closure plate membrane, discard Liquid, dry by swing, add washing buffer to every well, still for 30s then drain, repeat 5 times, dry by pat.
6.add enzyme:Add HRP-Conjugate reagent 50μl to each well, except blank well.
7.incubate:Operation with 3.
8.washing:Operation with 5.
9.color:Add Chromogen Solution A 50ul and Chromogen Solution B to each well, evade the light preservation for 15 min at 37℃
10.Stop the reaction:Add Stop Solution50μl to each well, Stop the reaction(the blue color change to yellow color).
11.assay:take blank well as zero , Read absorbance at 450nm after Adding Stop Solution and within 15min.
Steps description
Standard, Sample diluent |
Add Standard, Sample diluent, incubate for 30 min at 37℃. |
Wash 5 time,Add HRP-Conjugate reagent, incubate for 30 min at 37℃. |
Wash 5 times,Add Chromogen Solution A and B, incubate for 30 min at 37℃. |
Add Stopp Solution |
Read absorbance at 450nm within 15 min |
calculate |
Calculate
Take the standard density as the horizontal, the OD value for the vertical ,draw the standard curve on graph paper, Find out the corresponding density according to the sample OD value by the Sample curve, multiplied by the dilution multiple, or calculate the straight line regression equation of the standard curve with the standard density and the OD value ,with the sample OD value in the equation, calculate the sample density, multiplied by the dilution factor, the result is the sample actual density.
Important notes
1. The kit takes out from the refrigeration environment should be balanced 15-30 minutes in the room temperature, ELISA plates coated if has not use up after opened, the plate should be stored in Sealed bag.
2. washing buffer will Crystallization separation, it can be heated the water helps dissolve when dilute . Washing does not affect the result.
3. add Sample with sampler Each step, And proofread its accuracy frequently, avoids the experimental error. add sample within 5 min, if the number of sample is much , recommend to use Volley .
4. if the testing material content is excessively higher (The sample OD is bigger than the first standard well ),please dilute Sample (n-fold), Please diluente and multiplied by the dilution factor.(×n×5).
5. Closure plate membrane only limits the disposable use, to avoid cross-contamination.
6. The substrate evade the light preservation.
7. Please according to use instruction strictly, The test result determination must take the microtiter plate reader as a standard.
8. All samples, washing buffer and each kind of reject should according to infective material process.
9. Do not mix reagents with those from other lots.
Storage and validity
1.Storage: 2-8℃.
2.validity: six months
杭州co2激光焊接機_yag激光焊接機153-9155-1283杭州co2激光焊接機_yag激光焊接機
公司介紹: 楚天工業激光設備有限公司成立于1985年,是一家規模大、產品種類多、市場網絡健全的專業激光產品制造商。 楚天工業激光設備有限公司為全球客戶提供全面的激光加工解決方案和相關配套服務,其主要產品有激光焊接機、激光切割機、激光打孔機、激光標刻機、激光劃片機、激光溶覆機、激光熱處理機、太陽能電池激光加工機、激光加工機器人等十個系列百余種各類激光加工設備和配套服務。激光補焊的應用 激光模具焊接機焊接材料非常廣泛,括: 冷作高合金鋼、熱鍛高合金鋼、含鎳工具鋼、高級鋼、銅合金、鈹銅、高韌鋁合金等金屬材料。 激光模具焊接機;適用于如數碼產品、手機、玩具、汽車、摩托車等模具制造和成型行業。通過模具的修補,可以將原來的模具重新充分利用,大大節約了生產成本和提高了。機型特點
*焊斑能量分布均勻,具有焊接特性所需要的最佳光斑;
*適應各種復雜焊縫,各種器件的點焊;
*采用進口聚光腔體,更具有耐腐蝕、耐高溫、壽命更長久;
*具有24小時連續工作能力,整機工作性能穩定
應用范圍
應用于光通信器件、醫療、電池、光纖耦合器、顯像管電子槍、金屬零件、精密零件、各種模具、汽車鋼片等焊接行業。工作效率
• 相對于氬弧焊接等其它焊接方式,激光修補模具具有以下優點:
• 激光焊接點直徑只有0.2mm~2.0mm;
• 選用1064nm波長激光,對人體無害;
• 受熱范圍內小,不會出現變形,不會出現氣孔;可加工材料如,模具鋼、不銹鋼、鈹銅及貴重金屬等;
• 可修補裂痕、崩角、模邊、及磨損了的密封邊;
• 焊接過后可以磨削加工成光面;
• 可在極硬的材料上進行焊接(~HRC 60)。
杭州co2激光焊接機_yag激光焊接機 杭州co2激光焊接機_yag激光焊接機
產 品 說 明 | ||
|
低溫恒溫反應浴(槽)是我廠參照日本東京理化器械株式會社的同類產品改進制造的一種新型實驗儀器。適用于科研、生物、物理、醫藥、化工等部門進行低溫實驗,可代替干冰和液氮做低溫反應和相關設備提供低溫條件,又可以作為低溫水槽做運用粘度的測試,又可底部裝磁力攪拌,分兩段攪拌,使不銹鋼槽內溫度更均勻,智能控溫精確等特點。低溫恒溫反應浴的技術參數:
規格型號 | 儲液容積(L) | 空載調節范圍(℃) | 溫度波動度(℃) | 制冷量(w) | 環泵流量(l/min) | 實用開口徑 |
DFY-4/5 | 4 | -5~98 | ±0.5 | 135-165 | 4 | 120×80 |
DFY-4/10 | 4 | -10~98 | ±0.5 | 152-170 | 4 | 120×220 |
DFY-5/10 | 5 | -10~98 | ±0.5 | 170-195 | 4 | φ190 |
DFY-5/20 | 5 | -20~98 | ±0.5 | 242-920 | 4 | φ190 |
DFY-5/40 | 5 | -40~98 | ±0.5 | 205-1230 | 4.5 | φ190 |
DFY-5/80 | 5 | -80~98 | ±0.5 | 230-1200 | 4.5 | φ190 |
DFY-10/25 | 10 | -25~98 | ±0.5 | 300-2300 | 4.5 | φ220 |
DFY-10/30 | 10 | -30~98 | ±0.5 | 200-2600 | 4.5 | φ220 |
DFY-10/40 | 10 | -40~98 | ±0.5 | 230-1070 | 4.5 | φ220 |
DFY-10/80 | 10 | -80~98 | ±0.5 | 380-2600 | 4.5 | φ220 |
DFY-20/40 | 20 | -40~98 | ±0.5 | 648-2440 | 4.5 | φ290 |
DFY-20/80 | 20 | -80~98 | ±0.5 | 600-2800 | 4.5 | φ290 |
DFY-5/100 | 5 | -100~室溫 | ±0.5 | 90-1200 | 4.5 | φ190 |
DFY-5/120 | 5 | -120~室溫 | ±0.5 | 75-1500 | 4.5 | φ190 |
DFY-10/100 | 10 | -100~室溫 | ±0.5 | 90-1000 | 4.5 | φ220 |
DFY-10/120 | 10 | -120~室溫 | ±0.5 | 95-1200 | 4.5 | φ220 |
DFY-20/120 | 20 | -120~室溫 | ±0.5 | 100-1500 | 4.5 | φ290 |
YP 系列電子天平具有流暢新穎的外形設計,體現了對現代理念的追求。的設計,使稱重的反應速度更快,定點更迅速。穩定性和抗干擾性高。 本公司開發的YP系列電子天平還可以根據用戶的要求進行生產。具有強大的靈活性,野外操作的選擇。
特點:
交直流兩用,帶水準儀,液晶背光顯示,稱量反應速度快,高穩定性。
功能:
具有單位轉換(米制克拉、金盎司等)、穩定度、記憶功能、動物稱重、全量程去皮等多種功能,操作更簡便。
內置RS232C輸出接口,可直接連接計算機、打印機等外部設備。
| | | |
| | | |
| | | |
| | | |
| | | |
深圳市埃塔電子設備有限公司提供專業SMT全自動生產線解決方案,我們專業代理三星貼片機,作為三星貼片機的重要合作伙伴,埃塔一直致力于為客戶提供最佳的smt設備和服務,主要型號有SM411,SM421,SM321等設備,歡迎咨詢.我們還提供松下貼片機,FUJI貼片機,三星貼片機,YAMAHA貼片機/JUKI貼片機,西門子貼片機,富士貼片機,雅馬哈貼片機,無鉛回流爐,回流爐,無鉛波峰焊爐
胡梅13632709811
雅馬哈YC8特點:可貼裝最大尺寸達100mm×100mm、高達45mm的元件支持貼裝重達1kg的元件,還具備壓入元件的功能機身僅寬880mm的小型化設計,可最大限度地有效利用空間支持可裝最多15張托盤的自動更換式托盤供給裝置 ATS15支持SS型電動送料器與ZS型電動送料器
機型:YC8
對象基板:L50 x W50mm ~ L330 x W360mm (※1)
貼裟精度:
本公司評估用使用標準元件時絕對精度(μ+3σ) :±0.05 mm/QFP重復精度(3σ) : ±0.03 mm/QFP
貼裝能力:
參考指標:2.5 秒/元件(以吸附~識別-貼裝元件為1 個周期)
對象元件:4 x 4 mm -100 x 100 mm (※2)(超過45 x 45mm 的元件,一部分貼裝時有條件限制。)最大元件高度45mm最大載荷1 kg
元件供給形態:部件晶種數料帶盤:最多可裝28 個(以8mm 寬換算時)托盤:最多可裝15 張 料桿
電源規格:三相AC 200/208/220/240/380/400/416 V ±10% 50/60 Hz
供給氣源:0.45 MPa 以上、清潔干燥狀態
外形尺寸(突起部除外): L880×W1,440×H1,445 mm (主體)L880×W1,755×H1,500 mm (配備ATS15 時)
重量:約1,000 kg (主體)ATS15: 約120 kg
※1:關于最大可貼裝的基板尺寸請另行洽談協商。※2:關于規格外元件尺寸請另行洽談協商。
美國TYCO泰科執行機構執行機構 與泰科公司閥門系列直接裝配的多款氣動、液壓和直行程、角行程電動執行機構,具有免維護、長壽命、高性能的優點。
氣動執行機構齒輪齒條式 撥叉式高負荷撥叉式雙作用、單作用型故障安全電動執行機構緊湊型設計高負荷角行程、直行程和多回轉故障安全電動執行機構雙作用型故障安全深海專用
▲功能特點 |
快速更換軟管,具有自動適應卡管裝置,適用于多種規格軟管,滾輪均采用優質不銹鋼材質,具有很好的耐用性,泵頭外殼采用PSF或PPS材料,鋼性及結構性能優異,性能穩定,耐150℃高溫,不耐有機溶劑。 |
▲技術指標 |
|
▲流量曲線 |
|
▲泵頭外形尺寸 |
|