德森克電容標簽傳感器]-上海毅賓電氣專業銷售特點:槽距 0.4mm…1.0mm 輸出方式 pnp/npn NO/NC工作頻率高 max. 4.000HZ抵御外光 max. 100.000lux 短路保護連接插頭電纜、示教功能/遠程示教功能可檢測金屬、非金屬標簽此產品最適合用于印刷行業
德森克光電標簽傳感器]-上海毅賓電氣專業銷售特點:光源 紅外光槽距 2.0mm…5.0mm 輸出方式 pnp/npn NO/NC 亮通/暗通工作頻率高 max. 10.000HZ抵御外光 max. 100.000lux 防護等級高靈敏度可通過示教按鈕調節連接插頭電纜、示教功能/遠程示教功能此產品最適合用于印刷行業
此款獲獎的電容式透明標簽傳感器以其準確、可靠、穩定的配準完成對透明和紙質標簽的檢測。當更換滾軸或環境變化時,無需進行調節。此款透明標簽傳感器也是檢測接合處的絕佳之選!同時,對紙質標簽的檢測也異常精確。
電容技術是迄今為止速度最快的標簽檢測技術。更快速 = 更精確的配準和標簽位置。將其 20 微秒的響應時間與其他技術 300-500 微秒的響應時間進行對比。
對于金屬標簽或箔印刷圖案標簽 -選用 LRD6110。
響應時間 | 20 微秒 |
精確度 | 0.2 毫米 |
開關頻率 | 10 kHz |
操作溫度 | 4°C-50°C |
輸出 | NPN、PNP 開路集電極 |
輸入電源 | +11-28 VDC |
短路和超負荷保護 |
AutoGap Setup1. Start with High Gain off.2. Remove a label from the web.3. Place the area of the missing label in the sensor (liner only).4. Press for at least 1 second (lights begin to move back and forth).5. Release the button.6. Setup complete.7. Verify the light bar goes into the gray GAP area during gaps betweenlabels and into the gray LABEL area during labels. If necessary, usearrow keys to adjust manually.If light bar is not moving at least three or four lights, turn on High Gain.Manual AdjustmentWhen running, the light bar should extend from the gray LABEL area to thegray GAP area. The up and down arrows can be used to fine tune theadjustment if necessary.If the adjustments reach the end of their range, the last light in the GAP or LABEL area will flashthree times when the button is pressed.The light bar may move toward LABEL while the Up arrow is pressed. This is because the sensorbody is deflecting and making the slot smaller. It will return when the button is released and will notaffect setup.Metal/Foil Label SetupAutoGap Setup on a missing label area may not work reliably for rectangular metallic labels (foil ormetalized Mylar). In this case, place an actual gap in the sensor (use alignment groove on thesensor). Then hold the Gap button down for AutoGap as above. Move labels slowly through thesensor. Use manual adjustments if necessary to ensure the light bar is in the LABEL area duringlabels and GAP area during gaps. If the sensor still cannot be adjusted for reliable operation, youmay need the LRD8200 Ultrasonic Sensor.
LRD6300 電容式標簽傳感器可檢測多數標簽類型:透明、紙質、金屬藝術品、金屬油墨或燙印。還可檢測接合處!LRD8200 對于固態箔標簽(在箔上印有藝術圖案)的檢測尤為精確。
電容技術是迄今為止速度最快的標簽檢測技術。更快速 = 更精確的配準和標簽位置 - 可檢測多數標簽類型。將 LRD6300 20 微秒的響應時間與其他技術 300-500 微秒的響應時間進行對比。
響應時間 | 20 微秒 |
精確度 | 0.4 毫米 |
開關頻率 | 10 kHz |
操作溫度 | 4°C-50°C |
輸出 | NPN、PNP 開路集電極 |
輸入電源 | +11-28 VDC |
短路和超負荷保護 |
TRI-TRONICS® introduces the very first Ultrasonic Clear Label Sensor with a High Performance Graphic OLED display. The OLED display provides the user with an unprecedented view of the sensor's performance, options, program modes, and helpful simple instructions never before offered in a Clear Label Sensor. Designed into the sensor are all the Ease-of-Use characteristics that have made Tri-Tronics' sensors so well known in the industry.
The Ultrasonic Clear Label Sensor is the answer to what the industry has been asking for...
a simple solution, with the ability to accurately adjust for repeatable and reliable performance.
Now "CONFIDENTLY" walk away from the labeling line, "KNOWING" the throughput is at peak performance and trouble free.
Features & Benefits:To contact one of our well-qualified Distributors near you to assist you in your purchase, click the Distributor button. To purchase yourself, click the Buy Now button.
Available Clear Label Sensor Models:
Clear Label Sensor with 6' Cable:
CLS-1
Clear Label Sensor with Connector:
CLSC-1CLSC-1M8
While designed for label detection, the LABEL•EYE™ can be useful in a variety of applications:
Available LABEL•EYE™ Sensor Models:
LERLERCLERC-M12LERR
High Speed Models:
LERC10LERR10LERC10-M12
MSK1000-0256光柵磁柵尺編碼器SIKO讀數頭磁帶MB100磁位移位置測量傳感器磁性傳感器 MSK1000
聯系方式 131 16719459增量值編碼,數字化接口,分辨率0.2μm
特點:
■ 大分辨率 0.2μm
■ 重復精度 ±1μm
■ 與磁尺間距達 0.4 mm
■ LED狀態顯示
■ 堅固的金屬外殼
參數
名稱 數據 備注
磁尺匹配型號 MB100
系統精度 ±10μm 磁尺MB100 的精度等為10μm
重復精度 max. ±1μm
與磁尺間隙 0.1 ... 0.4 mm 參考信號 O,I
0.1 ... 0.2 mm 參考信號 RB
運動速度 取決于分辨率及脈沖間隔 參照表格
外殼材料 鋁壓鑄件 鋁制蓋,陽防銹處理
線纜類型 PUR 可裝保護鏈
工作溫度 -10 … +70 °C
存儲溫度 -30 … +80 °C
空氣溫度 100 % rF 防凝露
防護等 IP67
抗震性能 10 g/50 Hz
大測量長度 無限制 單卷大長度90 m
運動速度 Vmax (m/s)
分辨率(μm) 0.2 0.64 0.32 0.16 0.08
1 3.20 1.60 0.80 0.40
2 6.40 3.20 1.60 0.80
5 16.00 8.00 4.00 2.00
脈沖間隔時間(μs) 0.25 0.50 1.00 2.00
計數頻率(kHz) 1000.00 500.00 250.00 125.00
電氣參數
名稱 數據 備注
工作電壓 6.5 V DC ... 30 V DC UB 端帶性保護
4.75 V DC ... 6 V DC UB 端無性保護
電流能耗 < 25 mA 空載
連接方式 散裝線
圓型插頭
9 針D-SUB
輸出電路 LD, RS422
輸出信號 A, /A, B, /B, I, /I, 或 R, /R
參考信號脈沖寬度 1 或4 個增量
分辨率 0.2, 1, 2, 5μm
抗干擾等 3 IEC-610006-2
實時請求 實時信號輸出
信號高電平 > 2.5V
信號低電平 < 0.5V