COM-3200PROIICOM-3200PROII型專業高精密空氣動態負氧離子檢測儀
參數規格：
1、測定原理：電容器法。世界首創,準確度大大提高.
2、測定范圍：三段式設定
Ｒ1：0～20,000 個/cc （最大液晶表示：19,990Ｘ1）
Ｒ2：0～200,000 個/cc （最大液晶表示：19,990Ｘ10）
Ｒ3：0～2,000,000個/cc （最大液晶表示：19,990Ｘ100）
3、液晶顯示。顯示的數據為每立方厘米的負離子個數。
4、可進行環境測量，也可對釋放負離子的各種產品的測量。
5、安裝軟件，可通過電腦實時進行監測，數據可存儲在電腦上，以備隨時調出使用。通過軟件，溫度、濕度、負離子或正離子三種測量參數同時以曲線圖的形式實時顯示。測定時間長短可通過軟件設定。測量時間會記錄在存儲的曲線圖上。
6、電源要求 :AC100V-AC240V，內置可充電電池可連續使用6小時以上，2路電源。
7、ＲＳ－232Ｃ輸出接口，可以與電腦連接。
8、尺寸：70 ×寬110 ×縱長188毫米（不包括凸起部分）
9、內置溫濕度傳感器
10、溫濕度測定范圍：溫度：0～50．0℃ ；濕度：0～100％
11、漂移率：±5%
12、重量：1.5KG
配置:
主機,軟件,說明書,儀器箱,三腳架,適配器,數據線,
產地：日本
50-200淄博COD穿線管生產廠家
山東陽谷順通建材有限公司供應COD穿線管材，規格：50-200，質優價廉，服務有保障，如有需要，歡迎選購！
一氧化碳測試儀 MS400-CO
型號：MS400-CO
MS400一氧化碳測試儀簡介：
MS400一氧化碳測試儀用于便攜式快速檢測一氧化碳氣體濃度、溫濕度測量并超標報警的場合。MS400復合式四合一氣體檢測儀采用2.31寸高清彩屏實時顯示濃度，選用知名品牌的氣體傳感器，主要檢測原理有：電化學、紅外、催化燃燒、熱導、PID光離子。先進的電路設計、成熟的內核算法處理，取得了多項軟件著作專利和外觀專利。MS400可以檢測管道中或受限空間、大氣環境中的氣體濃度，可以檢測氣體泄漏或各種背景氣體為氮氣或氧氣的高濃度單一氣體純度，檢測氣體種類超過500種。
MS400一氧化碳測試儀特點：
● 防水濺、防塵、防爆、防震，本安電路設計，抗靜電，抗電磁干擾
●防護級別IP65，內置水汽、粉塵過濾器，防止因水汽和粉塵損壞傳感器和儀器
●內置泵吸式測量，響應迅速，采樣距離大于10米，特殊氣路設計，可直接檢測
負壓或正壓-0.5～2公斤的氣體，對測量結果無影響
●2.31寸高清彩屏顯示實時濃度、報警、時間、溫度、濕度、存儲、通信、電量、
充電狀態等信息，菜單界面采用高清仿真圖標顯示各個菜單的功能名稱
●大容量數據存儲功能，標配10萬條數據存儲容量，更大容量可訂制。支持實時
存儲、定時存儲，或只存報警濃度數據和時間、支持本機查看、刪除數據，
也可通過USB接口將數據上傳到電腦，用上位機軟件分析數據和存儲、打印。
●USB充電接口，可用電腦或充電寶充電，兼容手機充電器，過充、過放、過壓、
短路、過熱保護，5級精準電量顯示，支持USB熱插拔，檢測儀在充電時可正常工作，選配RS485通訊
●采用4500mA大容量可充電高分子聚合物電池，可長時間連續工作
●聲光報警、振動報警、視覺報警、欠壓報警、故障報警，報警時多方位立體顯示報警狀態。
●報警值可設，報警方式可選低報警、高報警、區間報警、加權平均值報警
●高精度溫濕度測量（選配），同時對傳感器進行溫度補償，儀器使用溫度范圍-40～70度，
可檢測400度的氣體，更高溫度的氣體檢測可訂制（選配高溫采樣降溫過濾手柄或高溫高濕預處理系統）
●可以選配同時檢測1～4種氣體，單位自由切換，常規氣體不需要輸入分子量，特殊氣體需要輸入分子量就
自動計算并切換，單位可選：PPM、mg/m3、Vol%、LEL%、PPHM、ppb、mg/L
●三種顯示模式可切換：同時顯示四種氣體濃度、大字體循環顯示單通道氣體的濃度、實時曲線，各通道
之間自動循環或手動循環可切換，可設置是否顯示最大值、最小值、氣體名稱，可查看歷史記錄曲線圖。
●中英文界面可選擇，默認中文界面，簡明中文或英文操作提示
●數據恢復功能，可以選擇性恢復或全部恢復，免去誤操作引起的后顧之憂
●零點自動跟蹤，長期使用不受零點漂移影響。
●目標點三級校準，保證測量的線性度和精度，能同時符合國家標準和地方計量局標準。
●濃度校準誤操作自動識別并阻止，能避免人為因素造成的不良。
●可以實時檢測或定時檢測（針對被測氣體的量比較小的情況），不檢測時可以把泵關閉以延長開機時間。
●可記錄校準日志、維修日志、故障解決對策，傳感器壽命到期提醒，下次濃度校準時間提醒功能
MS400一氧化碳測試儀技術參數：
檢測氣體：一氧化碳CO ，選配：同時檢測1～4種氣體濃度和溫濕度測量，視傳感器和現場環境而定
檢測范圍：0～100ppm、1000、2000、10000、20000、100000ppm、100%LEL、100%Vol可選，其他量程可訂制
分 辨 率：0.01ppm或0.001ppm（0～10 ppm）；0.01ppm（0～100 ppm），0.1ppm（0～1000 ppm），
1ppm（0～1000 ppm以上），0.1%LEL（0～100%LEL）、0.01%Vol或0.001%Vol（0～99.999%Vol）
檢測原理：電化學、紅外、熱導、PID光離子、催化燃燒，根據氣體類型、量程、現場環境和用戶需求而定
傳感器壽命：電化學原理2～3年，氧氣2年或6年，紅外5～10年，催化燃燒3年、熱導5年，PID2年
檢測方式：內置泵吸式，流量500毫升/分鐘
顯示方式：2.31寸320X240高清彩屏顯示,5按鍵操作
檢測精度：≤±3%（F.S）
線 性 度：≤±2%
重 復 性：≤±2%
報警方式：聲光報警、振動報警、視覺報警、聲光+振動+視覺報警、關閉報警可選
響應時間：T90≤20秒
恢復時間：≤30秒
工作電源：DC3.6V
電池容量：3.6VDC，4500mA大容量可充電高分子聚合物電池 ,帶過充、過放、過壓、過熱、短路保護功能
使用環境：溫度-40℃~+70℃；相對濕度≤0-99%RH（內置過濾器可在高濕度或高粉塵環境使用）
樣氣溫度：-40℃~+70℃ ，選配高溫采樣降溫過濾手柄，可檢測400度或更高溫度的煙氣濃度
溫度測量：-40℃~+120℃（選配） 精度0.5℃
濕度測量：0-100%RH（選配） 精度3%RH
數據存儲：標配10萬條數據容量，支持本機查看、刪除或數據導出，免費上位機通訊軟件
存儲功能默認為關閉狀態，可設置為開啟狀態，存儲時間間隔任意設置
通訊接口：USB（充電與通訊），選配RS485或RS232通訊接口
界面語言：中文或英文可設置，默認中文界面
防爆類型：本質安全型
防爆標志：Exia II CT4
防護等級：IP65，防塵、防水濺
外型尺寸：160×70×28mm(L×W×H)
重 量：300g
標準附件：說明書、合格證、保修卡、USB充電器（含數據線）、高檔鋁合金儀器箱 、鱷魚夾、
光盤（上位機通訊軟件）、濕度粉塵過濾器1個
選配附件：溫濕度測量功能、1.2 m 可伸縮采樣手柄（1-10米軟管，標準長度1米）、
高溫采樣降溫過濾手柄、高溫高濕預處理系統、濕度粉塵過濾器多個、掛繩
應用場合：石油、化工、醫藥、環保、煙氣分析、空氣治理等所有需要檢測氣體濃度的場合.
咨詢
河北澤葉科技有限公司
電話：15903109997 QQ:770110057
SIGNAL RECOVERY
the signal recovery model 5210 is the benchmark dual-phase lock-in amplifier against which others are judged. it is widely referenced in technical publications describing a diverse range of research applications including optical, electrochemical, electronic, mechanical and fundamental physical studies. we also offer a single-phase version, the model 5209.although the introduction of instruments using digital signal processing has brought advances in phase sensitive detection techniques, units using analog demodulators are still the first choice for many experiments. these include those requiring a true analog output, for example in some feedback control loops, or where the instrument is used to recover the envelope modulation of a "carrier" frequency. of course, they are also chosen for compatibility with previous experimental setups.
voltage or current inputs...the instrument includes a current preamplifier with two transimpedance settings and so can directly measure signals from current sources such as photodiodes. with an input impedance of down to typically only 25 w the resulting voltage generated across the source by the signal current is minimized for the very best performance.
continuous full-scale sensitivity control...as with all lock-ins the model 5210 has a range of calibrated full-scale sensitivity settings. however, unlike other units it also has a sensitivity vernier control, allowing the full-scale sensitivity to be set to any value between the calibrated values. suppose you are performing an optical transmission experiment and you want to measure transmission in terms of a percentage relative to that of a "reference" sample. all you need to do is put the reference sample in the optical path and press the auto vernier control on the lock-in. it will then adjust the sensitivity so that the display reads 100%. now replace the reference sample with the test sample and read the percentage transmission directly.
unique walsh function demodulators...the simplest method of implementing the phase sensitive detector at the heart of an analog lock-in is with a reversing switch driven at the reference frequency, giving excellent linearity, dynamic range and stability. this is known as a "squarewave" demodulator since the instrument responds to signals not only at the reference frequency but also at its odd harmonics. it offers much better performance than can be achieved by using a true analog multiplier, which requires the synthesis of a very pure reference sinusoid and is very non-linear when handling large levels of interfering signal.
squarewave demodulation is ideal for many applications, such as experiments using chopped light beams where the signal being detected is a square-wave, since the odd harmonics contain useful information. however in other cases the requirement is for "sinewave" or "fundamental" response where only signals at the reference frequency are measured.
in theory, a squarewave can be modified to a sinewave response by in-serting a low-pass or bandpass filter in the signal channel ahead of the demodulator. however this requires a highly se-lective filter in order to reject signals at the third harmonic without at the same time causing significant phase and magnitude errors for signals at the reference frequency.
the model 5210 uses a modified form of switching demodulator, known as the walsh demodulator, which multiplies the applied signal by a stepped approximation to the reference sinusoidal waveform. this gives a demodulator that does not respond to signals at the third and fifth harmonics, although it does respond to higher harmonics. a fourth-order signal channel filter is therefore included to reject these harmonics, giving a overall sinewave response. the advantages of the switching demodulator are thereby retained without the phase and magnitude errors associated with the use of highly se-lective filters.
the instrument can be switched to operate in either sinewave or squarewave mode, giving you the choice of the optimum detection method for your experiment. only signal recovery gives you this flexibility.
choice of signal channel filter modes…in the usual sinewave response mode, the filter is set to the bandpass or low-pass modes. but what if you are trying to measure a signal at twice the reference frequency in the presence of a strong signal at the reference frequency? in this case, the filter can be set to a notch (band-stop) mode and tuned to the reference frequency, leaving the signal at 2f unattenuated and easy to measure.
in addition to the main signal channel filter, a line-frequency rejection filter operating at 50/60 hz and/or 100/120 hz is also included, for elimination of troublesome line pickup.
high dynamic reserve...the combination of the walsh demodulator(s) and the signal channel filter gives the instruments a dynamic reserve of up to 130 db - implying that you can, for example, measure a signal of 1 礦 in the presence of an interfering signal of more than 1 v. no other analog lock-ins deliver this performance.
output filters...the output low-pass filters offer time constants in the range 1 ms to 3 ks, with all settings available at slopes of both 6 and 12 db/octave. in addition, the units include a rear-panel output giving the signal at the output of the in-phase (x-channel) demodulator with a time constant of typically only 100 祍, for use in those applications such as tandem demodulation where the largest output bandwidth is required.
synchronous adc trigger...the analog outputs from the demodulators, after filtering by the output low-pass filters, need to be digitized by an analog to digital converter (adc) for display or for transfer to the controlling computer. if this conversion is carried out asynchronously then the resulting values can display significant jitter. this is because the demodulator output contains not only the required dc level, but also signals at twice the reference frequency. when the output is sampled for conversion, this 2f signal means that some samples will be smaller and some larger than the mean.
of course, the 2f component can be reduced to any arbitrarily small value by increasing the time constant, but this reduces the response time to changes in input signal, slowing down data throughput. the model 5210 therefore offers a unique reference synchronous adc trigger mode, which guarantees that the output is sampled at the same point relative to the reference waveform and thereby removes this source of error.
internal oscillator...with the model 5210 there is no need to buy a separate oscillator to use as an excitation source for your experiment, since it includes one capable of generating a low distortion sinewave output signal over a frequency range of 0.5 hz to 120 khz. although in most lock-ins the frequency of the internal oscillator can be adjusted, in this instrument the amplitude can also be controlled over the range 1 mv to 2 v rms.
manual or computer control...in manual operation the backlit control setting indicators, the two digital displays and the analog panel meter makes the instrument very easy to use, with the settings of all the important controls being instantly visible. six auto functions further simplify control adjustment, while red overload and reference unlock leds warn of conditions which will result in measurement errors. all the front panel indicators can be turned off for use in blackout conditions.
the instrument includes gpib (ieee-488) and rs232 computer interfaces, allowing virtually all the controls to be operated, and all the outputs that can be displayed to be read, via simple ascii mnemonic-type commands. the communications interface parameters, such as baud rate and gpib address are set by front-panel controls, with no difficult dip switches to adjust.
compatible labview drivers are available for those researchers working in that environment while the unit is also supported by the srinstcomms activex control and sdk. it can also be used with our acquire? lock-in amplifier applications software package, which allows non-programmers an easy way to log the instrument outputs to a pc file. the labview driver and a demonstration version of the software, demoacquire, are available for download from this site.
化工廠用便攜式二合一氣體檢測儀 可燃/CO/H2S/O2任選兩種
化工廠用便攜式二合一氣體檢測儀 可燃/CO/H2S/O2任選兩種產品是一款便攜式又稱手持的二合一檢測儀，此款儀表的性價比目前是在整個氣檢儀行業中最好的，它的傳感器也是采用的進口的專用傳感器，所以說在檢測的靈敏度上也是最靈敏的。
此款產品現如今在氣檢儀行業中的地位占有大的市場，是無家能比的。它已被我公司隆重地推向市場多年，多年來經過在市場的洗禮現如今已銷往全國各地，受到各界人士的青睞。
此產品是一款國產知名品牌，此款產品的功能十分強大，它的存在關系到我們人員的安全是否得到有利的保障。此款產品自從被我公司隆重地推向市場以來，一直以來都得到客戶朋友的一直好評，也有越來越多的客戶朋友慕名前來進行選購。
化工廠用便攜式二合一氣體檢測儀 可燃/CO/H2S/O2任選兩種殼體采用阻燃ABS塑膠精鑄而成，防滑、防水防塵設計，適合使用于多種復雜場合。儀表為本安型防爆設計，防爆等級EX Ia iiB T3 Gb ,本產品通過國家防爆電氣產品質量監督檢驗中心檢驗，并取得防爆合格證，證號：CNEx12.3661x.
感謝您關注我們的產品,若您希望獲得進一步的了解，如 化工廠用便攜式二合一氣體檢測儀 可燃/CO/H2S/O2任選兩種等更多信息，歡迎您隨時聯絡我們，誠邀為您提供最滿意的服務!
主要技術參數：
●傳 感 器：氧氣及有毒氣體為電化學型,可燃氣體/催化式
●電 池：3.7V2000MAh鋰離子充電電池
●工作時間：可燃連續工作15小時、有毒氣體連續工作200小時
●顯 示：大屏幕中文液晶顯示
●報 警：聲、光、震動報警
●直接讀數：瞬間數值
●防爆標志：Ex ib IIB T3 Gb
●防護等級：IP67
●工作溫度：-20∽60℃
●工作濕度：5-90%RH
●尺 寸：126mm*66mm*33mm
●重 量：220g(帶充電器)
檢測氣體 量 程 精 度 最小讀數 響應時間
氧氣(O2) 0-30%vol ＜±5%(F.S) 0.1% vol ≤15秒
可燃氣體(Ex) 0-100%LEL ＜±5%(F.S) 1% LEL ≤15秒
一氧化碳(CO) 0-999ppm ＜±5%(F.S) 1ppm ≤25秒
硫化氫(H2S) 0-100ppm ＜±5%(F.S) 1ppm ≤30秒
HCA-200 COD（Cr)在線監測儀
|
|
產品簡介FRITSCH福里茨切割研磨機組合 “pulverisette 25 & pulverisette 19“ Cutting Mill Combination
適合處理成份極為復雜的樣品。
典型應用領域切割研磨機組合可使2 L 最大邊長為30 mm 的樣品尺寸減小到<500 μm，并在5分鐘內在一個通道內為分析提供代表性的樣品。在它眾多的應用中，最為主要的應用是根據標準方法對家庭垃圾分析提供不同樣品的制樣，或者是測定生熱值和氯氣含量。它是專門為處理如家用垃圾，建筑碎石，德國回收系統物品及回收的小型切碎機碎片等成分復雜樣品而設計的。
工作原理強力切割研磨機 “pulverisette 25”和通用切割研磨機 “pulverisette 19” 組成的研磨機組合的操作是從將樣品送入 “pulverisette 25” 開始的。研磨樣品進入通道，并在通道中進行進樣。進樣比率是可調的，但是標準分樣比率通常是1：13。
性能特點- 徹底的減少了清洗的需求- 適合處理成份極為復雜的樣品- 全自動化的兩部處理研磨過程- 通過氣旋式分離器收集樣品提取物- 方便樣品進料的設備- 無需工具便可移動研磨組件- 沒有篩分盤阻塞- 積分樣品分樣以減少精細研磨樣品的數- 通風冷卻操作- 流量大- 可允許樣品中含30％水蒸汽的操作
配置切割研磨機組合”pulverisette 25 - pulverisette 19” 訂貨號為19.5030.00的研磨機是用于常規應用的標準切割研磨機的組合。它包括帶2 L進料漏斗的強力切割研磨機和帶有進樣裝置，支架和通過氣旋式分離器的樣品抽吸裝置的通用切割研磨機，還包括碳化鎢的切刀和篩分盤。切割研磨機組合也可按照其它的構成組合，可使用“pulverisette 25” 和 “pulverisette 19”的任何附件。這些附件都可以在的各自的產品樣本中找到。
| 技術參數 | ||||||||||||||||||||||||||||
| ||||||||||||||||||||||||||||
| 適合下列的樣品 | ||||||||||||||||||||||||||||
|
泰科瑞迪優勢供應美國ACE Controls Inc.減震緩沖器
代理采購德國、美國進口工業品，進口儀器儀表，進口備品備件，歡迎咨詢15652307669
北京泰科瑞迪工業設備有限公司聯系人：張平 手機：15652307669電話：傳真：QQ：2851033727 E-Mail: tkrdzhang@126.com網址：http://www.tycorady.com 優勢品牌：工業閥門： Swagelok，OILGEAR，GO，Valtek，VELAN，PLAST-O-MATIC，GEMU，MAGNATROL閥門附件： Flowserve，auma，Westlock，Bettis，MARWIN，everlasting，masoneilan，PMV，TopWorx，STONEL 檢測儀表：pearson，Det-tronics，Fireye，AI-TEK，Durag，Teledyne，HYDAC，HEIDENHAIN工業過濾產品：HILCO，votech，NUGENT，BOLL&KIRCH，Des.Case，Vickers MAHLE，CJC工業電器：FSG，Dongan，SOR，ITT，Hammond，DELTA CONTROLS，IMAV，barksdale，Chromalox，RENCO，Dynapar，GEMCO，CESOVENT，BLACK BOX，AEG，CELESCO，AUTOTECH工業流量儀表：Brooks，NOSHOK，HEDLAND，KencoGE燃機備件：美國GE燃機熱電偶氣動元件：EDCO真空產品 PIAB真空產品 AIRPOT AIRPEL氣缸機械傳動：DAYTON，NEXEN，LESSON，ATBChar-lynn，VERSA-MATIC
美國ACE Controls Inc.減震緩沖器
北京泰科瑞迪工業設備有限公司供應美國ACE Controls Inc.減震緩沖器，如您有意購買，歡迎來電咨詢！
美國ACE Controls Inc.，世界減震技術的領導者，致力于為用戶提供高性價比、世界一流的減震產品，以提升客戶在國際市場的競爭力。減震器的主要用途是在機器設備中緩沖負載沖擊、避免碰撞損害、消除噪音、提高循環速度、提升產品品質等。 ACE高性能減震緩沖器產品廣泛應用于自動化、機器人、物料傳輸、包裝、鋼鐵、機床、木材、娛樂、醫藥等各行業。
型號如下：
comCAA4X6-F-7,CAA4X6-FRP-5,CAA4X6-FRP-7,CAA4X6-R-5,CAA4X6-R-7,CAA4X6-RP-7,CAA4X6-S-3,CAA4X6-S-5,CAA4X8-C-5,CAA4X8-F-5,CAA4X8-FRP-3,CAA4X8-R-3,CAA4X8-RP-3,CAA4X8-S-3,CAA4X8-S-5,CAA4X8-S-7,CB100F,CB100R-STROKE100,CB100F,CB100R-STROKE200,CB100F,CB100R-STROKE300,CB100F,CB100R-STROKE400,CB100F,CB100R-STROKE500,CB100F,CB100R-STROKE600,CB100F,CB100R-STROKE800,CB100FB,CB100RB-STROKE100,CB100FB,CB100RB-STROKE200,CB100FB,CB100RB-STROKE300, CB100FB,CB100RB-STROKE400,CB100FB,CB100RB-STROKE500,CB100FB,CB100RB-STROKE600,CB100FB,CB100RB-STROKE800,CB160F,CB160R-STROKE100,CB160F,CB160R-STROKE200,CB160F,CB160R-STROKE300,CB160F,CB160R-STROKE400,CB160F,CB160R-STROKE500,CB160F,CB160R-STROKE600,CB160F,CB160R-STROKE800,CB160FB,CB160RB-STROKE100,CB160FB,CB160RB-STROKE200,CB160FB,CB160RB-STROKE300,CB160FB,CB160RB-STROKE400
北京泰科瑞迪工業設備有限公司供應美國ACE Controls Inc.減震緩沖器，如您有意購買，歡迎來電咨詢！